Plot Plan Dwg Autocad Drawing

The information in this article applies to:

QUESTION

I would similar to know how to create a plot plan in Chief Architect. How is this accomplished?

ANSWER

A plot programme is substantially a map of a property's legal description. This article describes how to create an accurate plot plan by inputting lines, arcs and setbacks using the CAD tools available in Primary Architect.

• Creating a plot program polyline
• Correcting an mistake
• Creating a curved property line
• Displaying line length, angle, and arc radius information
  
• Creating setback lines
• Accurately positioning a building
  
• Converting a plot plan to a terrain perimeter
  

To create a plot programme polyline

1. Select CAD> Points> Input Indicate from the carte du jour to open the New CAD Betoken dialog.
2. Select Absolute Location, define the point's position at (0,0) for the X Position and Y Position, then click OK.

   This is the current indicate and will serve as the Starting time Point for the offset line of the plot programme.

   

3. From the bill of fare, select CAD> Lines> North Arrow , and so click and drag the line upward to create a Due north Pointer pointing up to the top of the screen.
4. Select CAD> Lines> Input Line to open the New CAD Line dialog once over again. Notice that the First Point is (0,0), which is the location of the current point that yous only created. Click the Number Style button at the bottom of the dialog and in the Dialog Number/Angle Style dialog:
   
   
   • Select Decimal Feet for the Number Style.
   • Cull the Angle Fashion that matches your data, such as Quadrant Bearing or Azimuth Bearing.
   • Click OK.
     
5. Staying in the New CAD Line dialog, select the Relative to Offset Bespeak option and bank check Polar. Enter the length of the first side of your property boundary'southward legal description in the Altitude field, and the bending of that line in the Bending field.

   

6. Click Side by side and enter the Distance and Bending of the next holding line.

   The next property line volition be the ane bordering the end point of your first line, rather than the start betoken.

   

   Note: With the North Arrow pointing in the upwardly direction, an angle of 90 degrees will travel in the direction of left to right, 0 degrees volition go from bottom to top, 270 degrees will go from right to left, while 180 degrees will travel from acme to bottom.

   
   
7. Continue until all holding lines are entered, then click OK to close the dialog.

   The property line created should be airtight, with the finish-point of the last line being the same as the start signal of the outset line.

   

   If you lot take received plot plan information from a surveyor, keep in mind that any given line can be described in 2 means using Quadrant Bearings, and non all surveyors will describe the lines of a given plot in the same direction (ie, clockwise or counterclockwise).

   If the lines are not described in the same direction, then your issue volition not exist a closed polyline.

   
   

To correct an mistake

1. If a line is entered incorrectly, click OK to close the New CAD Line dialog.
2. Click on the incorrect line to select information technology, so click on the Disconnect Selected Edge edit button.
3. With the wrong line at present separate from the rest of the polyline, it can at present exist deleted. Select the Delete edit push or the Delete key on your keyboard.
4. Place a CAD point at the end of the last correct line using the Place Point tool to create a new current signal.
5. Select the Input Line tool and keep entering information in the New CAD Line dialog as described in the department above.

To create a curved property line

1. Click on an existing property line to select information technology, then click the Modify Line/Arc edit button to plow this line into an arc.
2. If necessary, use the triangular reshape edit handle to brand the arc concave or convex.
3. Click the Open Object edit push button to open the Polyline Specification dialog.
4. On the Selected Arc console, click the Chord radio button nether the Lock category, specify the length of the Radius, then click OK.

   In this example, a value of 65' is specified.
   
   

   A curved property line can also be created by inbound data in the New Arc dialog. See the Chief Architect Reference Transmission for more information.

To display line length, angle, and arc radius information

1. Select Edit> Default Settings from the carte, expand the CAD category, select General CAD, then click the Edit button.
2. In the CAD Defaults dialog:

   

   • Cull the bending display method that matches your data under the Display Line Bending every bit section.
   • Click on the Define push button nether Displayed Line Length Format Preview to display the Displayed Line Length dialog, and under Accuracy, select the Decimal Places radio push button

     

   • Click OK and/or Done on all dialogs to ostend the changes.
     
3. Click on the plot plan polyline to select it and click the Open up Object edit button.
4. On the Line Style console of the Polyline Specification dialog:

   

   • If y'all're using the Plot Program Saved Plan View, the plot plan may already be on the CAD, Plot Programme layer.

     If y'all're non using the Plot Programme Saved Plan View, change the layer to CAD, Plot Program, click the Define push adjacent to the Layer drop-downwards, and ensure that the CAD, Plot Plan layer is set to exist displayed.

     For more information on layers and layer sets, delight come across the Related Articles section below.

   • Check Prove Length, Show Bending and All Angles.
   • Click OK to shut the dialog and utilize your changes.
     

To create setback lines

1. Select Edit> Preferences if you're on a Windows PC or Chief Architect> Preferences if you're on a Mac, and on the Behaviors panel of the Preferences dialog:

   

   • Select the Concentric radio button under Edit Type.
   • In the Jump field, type in the setback distance required by your local planning section
   • Click OK to close the dialog and utilize your changes.
     
2. Click on the plot programme polyline to select it, and so click the Copy/Paste edit push.
3. Place your cursor over a corner edit handle, then click and drag towards the center of the polyline. When a second, inner polyline displays, release the mouse.

   

4. Select the inner polyline and click the Open up Object edit button.
5. On the Line Style console of the Polyline Specification dialog:

   

   • Click the Ascertain button side by side to the Layer drop-down and in the Layer Display Options dialog that displays, click the Copy button to copy the layer, and change the name of the newly created layer to CAD, Setback.
   • Alter the Line Way to a dashed line style.
   • Uncheck the Show Length and Show Angle boxes, if desired.
   • Click OK to shut the dialog and apply your changes.
     
   
6. One time the setback is created, navigate to Edit> Edit Behaviors and select the Default option to switch back to the default edit behavior.

To accurately position a building

1. Navigate to CAD> Points> Place Point and identify a point along the perimeter of the belongings, such as a corner. Alternately, use the starting point for your plot programme polyline, (0,0), as a reference.

   

2. Select CAD> Points> Input Point to open the New CAD Betoken dialog.
3. Select Absolute Location and specify the desired altitude that the building will be from this bespeak in the X Position and Y Position fields.
4. If you have placed a CAD point at a different location, select Relative to Current Indicate and specify the desired distance from that point. Unless y'all would like to specify the location in distance and begetting, Polar (CCW from horz) should remain unchecked.
5. When you click OK, a bespeak will be created at the specified location. Use this betoken equally a reference to accurately position a wall or corner of the building.

To convert a plot plan to a terrain perimeter

If yous'd like to have your Plot Plan appear in 3D views as a grass pad with a thickness, you can convert it to a Terrain Perimeter.

1. Select the plot plan polyline and click the Convert Polyline edit push button.
2. In the Convert Polyline dialog, select Terrain Perimeter, specify the Layer you would like the Terrain Perimeter to continue, then click OK.
   
   
3. Make any needed changes, then click OK to close the dialog.

   The plot plan polyline that you created is now your Terrain Perimeter.

lennonstlef1976.blogspot.com

Source: https://www.chiefarchitect.com/support/article/KB-00575/creating-a-plot-plan.html

Bagikan Artikel ini